Tag Archives: upa usb

Motorola HC05E6 Pinout to Carprog Full

Part 1: Which tool is best for Motorola HC05E6 reading?

 

UPA USB 1.3 would be better for this then you can run connection test and work out which pin/wire is wrong or which pin needs lifting

Carprog programmer should work if it doesn’t then its wired incorrect to chip or other pins need lifting
ill see what upa manual shows in regards to wiring and pin lift for this chip.

 

Xprog only lift Pin-1.
Tested on many Benz key mcu MC68HC05E6 (011, 021, 040, 051)

 

Carprog or x-prog work good with hc05e6

 

Read to xprog lift 1 pin

 

For xprog programmer you need lift up leg 1,12 & 15
and for UPA-USB lift up leg 1, 11, 12, 15 & 16
Don’t forget to set oscillator 2 khz or 4 khz
Tested many time
Good luck

 

In summary, UPA-USB, Xprog, Carprog all has luck with Motorola HC05E6 reading.

 

Part 2: Carprog programmer read MCU MC68HC05E6

Read in key the MCU MC68HC05E6(0F82B)

carprog-read-key-chip

CarProg read Opel HC05 PIN

(it’s Opel immobiliser 1996-1998)

HC05-reading-with-CarProg

NOTE: for HC05, HC08, HC11, HC12, you need an A10 adapter or just buy Carprog full kit with 21 adapters

 

Carprog A10 adapter wiring diagram:

carprog-a10-adapter-wiring-diagram

CarProg A10 adapter crossreference to others tools cables

A10-mcu-cables-colors

Part 3: Motorola HC05 connection with Carprog v8.21 full

 

MC68HC05B6, MC68HC05B8, MC68HC05B16, MC68HC05B32

carprog-Motorola-HC05-1

carprog-Motorola-HC05-2

MPUMask Set

MC68HC05B6 0B91T

1C14H,

2C14H

0F10V

1E50H

 

MPU Mask Set

MC68HC05B8 0B83T

3D33J

0D54J

 

MPU Mask Set

MC68HC05B16 0D20J,

1D20J,

2D20J,

3D20J

0D60J

0F62J

1G28F

1G35N,

2G35N

http://obd365.blogrip.com/2017/05/05/motorola-hc05e6-pinout-to-carprog-full/

Vauxhall Meriva MC68HC08AZ32 pinout to XPROG

I have successfully read Motorola MC68HC08AZ32 chip data by using Xprog-M v5.55 ecu programmer. Pinouts and operations are attached below.

 

Model:

Vauxhall Meriva 1.7 (z17dth)
Part number:
6235248
93177230

 

Why i need ECU programmer?

Meriva 1.7 has engine failure. I have fixed the engine and its running normal now.
I have the airbag light in the dash.
Two airbags has deployed, so that’s why I have mounted resistors to trick the ecu, BUT!
This ecu can only be used one time.

 

And Xprog-m is the most populous in my post for ecu programmer suggestion.

 

How to connect Xprog to the chip MC68HC08AZ32A?

xprog-read-mcu

xprog-m-read-MC68HC08AZ32

Mask sets: 0J66D

Oscillator: 58, 59 pin

Packages: QFP64

EEPROM: 0x0800 – 0x09FF
How to read Motorola MC68HC08AZ32 with Xprog-M?

I solder the mcu back to the board and added the 8 wires, without desoldering all chip.

and read Motorola MC68HC08AZ32 with Xprog-M 5.55 (UPA USB programmer also ok),

then put damp here and get new damp clear, without crash data.

xprog-m-read-MC68HC08AZ32-1.jpg xprog-m-read-MC68HC08AZ32-2 xprog-m-read-MC68HC08AZ32-3

https://eobd21.wordpress.com/2016/08/23/xprog-v555-read-vauxhall-meriva-mc68hc08az32/