Tag Archives: Lonsdor K518ISE

Program Citroen Beringo 2012 Key by Lonsdor K518ISE

Lonsdor k518ise key programmer has successfully read pin code and program key on a Citroen Berlingo year 2012.

 

Guide:

Connect K518 host with vehicle via OBD diagnostic socket

Select Immobilizer->Citroen->Berlingo->Read Pin Code

k518ise-citroen-berlingo-8

k518ise-citroen-berlingo-7

Communicating

k518ise-citroen-berlingo-1

Turn ignition switch on

Current progress 40%
k518ise-citroen-berlingo-2

Turn ignition off

k518ise-citroen-berlingo-3

Communicating

Turn ignition on

k518ise-citroen-berlingo-4

k518ise-citroen-berlingo-5

Current progress 60%

Turn ignition off

Turn ignition on again

Current progress 80%

Turn ignition off

Turn ignition on

Lonsdor K518ISE read pin code success

k518ise-citroen-berlingo-6

Back to menu, select from vehicle->Berlingo->Immobilizer->Type 2->Program key

k518ise-citroen-berlingo-7

k518ise-citroen-berlingo-8

k518ise-citroen-berlingo-9

k518ise-citroen-berlingo-10

k518ise-citroen-berlingo-11

If K518 shows communication failure error means you have selected the wrong immo type

k518ise-citroen-berlingo-12

Go back and select immo Type 3

k518ise-citroen-berlingo-13

Communication success. Lonsdor K518 read vehicle information, VIN, PSA number etc successfully

k518ise-citroen-berlingo-14

Enter pin code to access

k518ise-citroen-berlingo-15

Turn ignition on then off within 15 sec

k518ise-citroen-berlingo-16

Program completed.

k518ise-citroen-berlingo-17

Test the new key and start vehicle.

www.obdii365.com

Program Key on Ford Focus 2013 with Lonsdor K518ISE

New feedback: Lonsdor K518ISE key programmer added an immobilizer key on a Ford Focus year 2103 middle east model.
Connect K518 host with vehicle via OBD diagnostic socket
Select Immobilizer->Ford->Focus->New Focus->2011-2013->Immobilizer->Add key
lonsdor-k518-ford-focus-1
lonsdor-k518-ford-focus-2
lonsdor-k518-ford-focus-3
lonsdor-k518-ford-focus-4
lonsdor-k518-ford-focus-5
lonsdor-k518-ford-focus-6
Insert new key and turn ignition switch on
Communicating
lonsdor-k518-ford-focus-7
Lonsdor K518 detect keys programmed:2
lonsdor-k518-ford-focus-8
Configuring system…
Reading pin code
lonsdor-k518-ford-focus-9
Read pin code success
Configuring system
lonsdor-k518-ford-focus-10
Lonsdor K518ise displayed key numbers programmed successfully
Program completed
lonsdor-k518-ford-focus-11

How to use Lonsdor K518 to change Jaguar XJ 12 mileage

Lonsdor K518ISE key programmer is able to change mileage on Jaguar XJ, F-type, and XE 2015 up (some pre-2015) models. Here’s demo guide on XJ year 2012 (Middle East model) odometer correction with K518ISE by OBD.
lonsdor-k518-change-jaguar-xj-km-1
A Jaguar XJ year 2012 running 157,999 km.
Connect K518 host with vehicle
Select Odometer Adjustment function->Jaguar->XJ->Odometer correction
lonsdor-k518-change-jaguar-xj-km-2
lonsdor-k518-change-jaguar-xj-km-3
lonsdor-k518-change-jaguar-xj-km-4
Turn ignition on
lonsdor-k518-change-jaguar-xj-km-5
Communicating
Manually enter mileage you desired, i.e: 141,000 km and confirm
lonsdor-k518-change-jaguar-xj-km-6
Change mileage in progress
lonsdor-k518-change-jaguar-xj-km-7
Dashboard instrument turns black during the procedure, it is normal. When change km is done, it will reset instrument.
lonsdor-k518-change-jaguar-xj-km-8
lonsdor-k518-change-jaguar-xj-km-9
Jaguar XJ mileage correction is done.
Turn ignition off and on
lonsdor-k518-change-jaguar-xj-km-10
lonsdor-k518-change-jaguar-xj-km-11
Lonsdor k518 key programmer automatically erase the fault code existed
lonsdor-k518-change-jaguar-xj-km-12
lonsdor-k518-change-jaguar-xj-km-13
Done.
Reference:

Top 3 Tools to Read VW Pin code by OBD

There are several tools available to read pin code and program key for VAG group. Here are the demo guides to read pin code for VAG.

 

1) Read VAG Pin Code with Lonsdor K518

Lonsdor K518ISE/K518  key programmer comes with built-in Volkswagen 4th & 5th adapter, so it can read pin code and program key for VAG 2th, 3th, 4th, 5th Immobilizer by OBD directly.

Vehicle tested:

VW Santana 3000 year 2010 with 44 chip

Connect Lonsdor K518 with vehicle

Select Immobilizer->Volkswagen->2th& 3th Immo->Read Pin code->Engine

lonsdor-k518-read-vw-pin-1

lonsdor-k518-read-vw-pin-2

lonsdor-k518-read-vw-pin-3

lonsdor-k518-read-vw-pin-4

lonsdor-k518-read-vw-pin-5

Turn ignition ON

Reading pin code…

lonsdor-k518-read-vw-pin-6

K518 will read VW VIN, PIN and CS after 5 seconds.

lonsdor-k518-read-vw-pin-7

 

2)Read VW Pin code with Xtool X100 Pad2

To read pin code and program key for VAG 4th 5th Immo, you need Xtool KC100 VAG 4th 5th Immo adapter to work with.

main steps:

Select VW/Audi/Skoda/Seat->4th 5th Immobilizer system

Turn ignition on

select 4th immobilizer
select instrument tyye
Turn ignition on
read immo code

xtool-x100-pad2-read-vw-pin
Read pin, cs, vin success

 

 

3) Read Pin code with Xhorse VVDI2 VAG

all user of VVDI2, you can provide serial number to activate authorization for EDC17 and MEV17 for online CS calculation.

vvdi2-vag-pin

www.obdii365.com

How to use Lonsdor K518 to Program Jaguar XJ Smart Key All Keys Lost

Lonsdor K518ISE key programmer is able to program smart key/all key lost for Jaguar, including F-type, S-type, XF and XJ.  Here’s the demo guide on programming smart key on a new Jaguar XJ when all keys lost with K518 (Chinese version) by OBD.

lonsdor-k518-jaguar-1

lonsdor-k518-jaguar-1-1

Procedure:

Connect K518ISE host with vehicle via diagnostic socket

Turn ignition ON

Select Jaguar->XJ->Program Smart key-> All keys lost

lonsdor-k518-jaguar-2

lonsdor-k518-jaguar-3

lonsdor-k518-jaguar-4

lonsdor-k518-jaguar-5

Lonsdor K518 requires at least 2 smarts key to be programmed

lonsdor-k518-jaguar-6

Turn ignition OFF

Cummincating

Read Part number and then software version etc

lonsdor-k518-jaguar-7

Identify key number. No key has been programmed.

lonsdor-k518-jaguar-8

Press YES to program new smart key

lonsdor-k518-jaguar-9

Keep the smart key to be programmed in hand

lonsdor-k518-jaguar-10

Programming…

Press the Unlock button on smart key for once within 5 sec

lonsdor-k518-jaguar-11

Unlocking

Press the Unlock button on smart key for once within 5 sec (repeat this step fro 3 times!)

lonsdor-k518-jaguar-12

1st key has been programmed successfully

lonsdor-k518-jaguar-13

Lonsdor K518ISE will ask whether to program next key. Press YES to program second key

Follow steps above to program next smart key

lonsdor-k518-jaguar-14

Identify number of keys programmed: 2

lonsdor-k518-jaguar-15

Program success.

lonsdor-k518-jaguar-16

Remote control will be generated automatically after programed smart key

Test the new smart key

lonsdor-k518-jaguar-17

Working. Done.

http://www.obdii365.com/producttags/lonsdor-k518ise.html

OBDSTAR X300 DP Full vs. Lonsdor K518 Key Programmer

Obdstar X300 DP vs Lonsdor K518ISE: what’s the difference? which tool is better for auto key programming?

 

This is a chart of the two, compared in terms of hardware, operation and functionality.

 

Hardware specification comparison:

Item Obdstar X300 DP Lonsdor K518ISE
Image obdstar-x300-dp-full-1 lonsdor-k518ise-web
Operating system Android 5.1 Android 4.4
CPU Samsung Exynos4418 A9 industrial-grade processor ARM V7
Storage space FLASH 16G FLASH 8G
RAM 2G 1G
Battery 7400mAh 4550mAh
Resolution 1280*800 1024*600
Screen size 7 inch 7 inch
HDMI Available No
Communication USB/Bluetooth USB only
WIFI Yes Yes
Dimension 215*147*30
Shell Three proofing and industrial-grade shell with rubber coating Civil-grade

Operation & service comparison:

Item Obdstar X300 DP Lonsdor K518
One key update Yes Yes
One key enter Yes No
Database Built-in repair database (domestic) No
Technical support Expert service team Professional service team

Function comparison:

Item Obdstar X300 DP PAD Lonsdor K518 Key Programmer
OBDII diagnosis Yes, full-system diagnosis No
Odometer correction Yes Yes
Pin code Inquiry 7*24 hours automatic Inquiry is available for most pin code (domestic) No
Key programming Yes Yes, it has full vehicle coverage, incl. Renault, Volvo, etc.(see details below)
EEPROM/PIC adapter Yes No
ABS Yes No
TPS Yes No
SRS reset Yes No
TPMS(low tire)reset Yes No
Steering angle reset Yes No
CVT learning/Value reset Yes No
EPB Yes No
Oil/service reset Yes No
Battery matching Yes No

In summary,

 

Obdstar X300 DP Pad: full system, multi-function including special functions

Lonsdor K518ISE: Expert in auto key programming! (with fullest vehicle coverage)

 

 

Lonsdor K518 is the NO.1 car key programmer in the word. And It has built-in Volkswagen 4th & 5th adapter and built-in chip & remote detection module. Compared with other universal key programming machines, it has the best vehicle coverage, including some keys cannot be programmed before, such as

Volvo (S40, S60, S80, XC60, XC90, C30, C70, V40, V60, V70) key programming
Toyota/Lexus: smart key all key lost – via OBD ( without dismantle)
BMW CAS3/CAS3+/CAS3++: direct OBD programming
BMW CAS4/CAS4+: dismantle & read data programming
BMW FEM system key programming & All keys lost
2016 -New Maserati: smart key programming
2016 -New Ford: smart key programming
Hyundai / Kia 46/47/8A smart key: PIN code reading via OBD, all key lost included.
Renault ( Megane, Koleos, Scenic) without PIN code key programming
VAG group 4th & 5th immobilizer system
Ferrari (458, F12, F149): direct OBD programming
Peugeot /Citroen: two ways to read PIN code & programming, all keys lost included

 

 

Lonsdor K518ISE IMMOBILIZER Car List: (support all cars)

Europe:
Audi, BMW, Benz, VW, Volvo, Citroen, Ferrari, Maserati, Fiat, Lamborghini, Jaguar, MG,
Land Rover, Bentley, Lancia, Opel, Peugeot, Porsche, DS, Renault, Alfa Romeo, Smart,
Borgward

America:
Cadillac, Chevrolet, Dodge, GMC, Buick, Hummer, Ford, JEEP, Lincoln, Mercury

Asia:
Honda, Hyundai, Isuzu, KIA, Lexus, Mazda, Mitsubishi, Nissan, Ssangyong, Subaru, Suzuki,
Toyota, Shigaoka Queen

China:
Iveco, Trumpchi, BYD, Geely, Chery, Great Wall, Young Lotus (Basically all Chinese car
models are included)

Lonsdor K518ISE vehicle list

Lonsdor-K518ISE-key-programmer-car-list-1Lonsdor-K518ISE-key-programmer-car-list-2Lonsdor-K518ISE-key-programmer-car-list-3

Program BMW FEM Key with K518, CGDI BMW, VVDI2 or Yanhua BMW FEM

Lonsdor K518ISE, CGDI Prog BMW, Xhorse VVDI2, Yanhua BMW FEM/BDC key programmer all are verified to program FEM/BDC key without issues. But which tool is best for BMW FEM BDC key programming?

 

Look here and you’ll know all:

bmw-fem-bdc-key-programmer

Lonsdor K518ISE program BMW FEM BDC key

CGDI Prog BMW OBD program FEM key

Xhorse VVDI2 BMW do coding/programming to FEM BDC

Yanhua BMW FEM key programmer add a new key

 

lonsdor-k518ise-fem-bdc-key-programmer

1 How to use Lonsdor K518ISE to program BMW FEM BDC key?

 

Three steps: read key info–>pre-process FEM/BDC system–>make a dealer key

In details…

 

Step 1: read key info

MUST read key information first

 

Step 2: pre-process FEM/BDC system

MUST DISCONNECT THE BATTERY

 

1: OBD back up original coding data:

On the car or test platform, connect to FEM/BDC system, then back up original back up coding files via OBD

2: read out EEPROM backup data & generate a service-mode EEPROM:

-> Disassemble FEM/BDC module, find out chip 95128 or 95256, read EEPROM data using a ECU programming tool: VVDI-Prog, Orange5 and the like;

-> Copy the EEPROM data into to the Lonsdor K518ISE customfile folder;

-> Run the program, read original EEPROM data and generate a service-mode EEPROM, upload data of the service-mode EEPROM, write it into chip 95128 or 95256 with help of a ECU programmer

-> Restore FEM/BDC system, supply battery to the car and connect via OBD

Lonsdor-K518ISE-program-BMW-FEM-BDC-key-1

3: programming

-> This step need to be done on the BMW FEM/BDC test platform;

-> Make sure that Step 1 & 2 is finished

-> Connect FEM/BDC system to power supply and connect to the OBD port

 

4: restore EEPROM data

-> disassemble FEM/BDC module, write original EEPROM data (Step 2) into chip 95128/95256

-> restore FEM/BDC system, connect to OBD

 

5: restore coding data

-> load the backup coding files (Step 1), restore coding information via OBD

 

6: pre-processing is complete.

 

Step 3: make a dealer key

 

1: Lonsdor K518ISE read out data, select the will-be key position

2: a “used”key to make a dealer key

All keys lost: enter 32bit ISN codes to make a dealer key

3: put the key near the car immo induction loop

Lonsdor-K518ISE-program-BMW-FEM-BDC-key-2

4: detect the original key, read out immo data

5: put a new key near the car immo induction loop

6: detect the key key, key learn (don’t move the key, keep stable)

7: key learn is complete

 

Step 4: disable the key

 

1: Lonsdor K518ISE read out data, select the key ID position to disable

2: put a “used” key near the car induction loop

3: K518ISE system tries to connect to CAS, disable the key with current ID position, disable key successfully

 

Step 5: enable the key

 

1: Lonsdor K518ISE read out data, select the key ID position to enable

2: put a “used” key near the car induction loop

3: K518ISE system tries to connect to CAS, enable the key with current ID position, enable key successfully

 

Step 6: delete the key

 

1: K518ISE read out data, select the key ID position to delete

2: read FEM/BDC key password

3: delete the key successfully; the key position is blank

 

THE MOST IMPOERTAN TIPS

1: You must read key info before everything you’ll do

2: to pre-process FEM/BDC, you should pay attention to:

– backup coding codes to continue

– disconnect to the power supply/battery, have a ECU programmer to read EEPROM data, up load data in K518 customfile folder, read new EEPROM data loaded just now, generate service-mode EEPROM data, read service-mode EEPROM data, write data into the chip, install CPU on the car

– ECU programming: need 6 min, with power supply connected

– disconnect to the power supply, disassemble CPU, write the original EEPROM data into the chip, install CPU on the car, connect to the power supply, make sure communicate is successful

– upload coding files (Step 1), restore original coding info to pre-process, then make a dealer key

3: 32bit ISN codes is required to program a new key when ALL KEYS ARE LOST

 

Job’s done with Lonsdor K518ISE!

 

cgdi-prog-fem-bdc-key-programmer-bmw

2 How to use CGDI Prog BMW to OBD program FEM key

 

Go to BMW OBD Key Match

CGDI-BMW-FEM-program (1)

The current FEM/BDC needs to update the ECU program before performing key matching. Please ensure that the car battery has enough power, the programming process, please keep the equipment cable connection

CGDI-BMW-FEM-program (2)

Please remove the FEM/BDC and then use the CGDI Prog programmer to read and save data from the P5XXX EEPROM chip on the FEM/BDC computer board, then click on Next

CGDI-BMW-FEM-program (3)

Read the original car EEPROM data file

CGDI-BMW-FEM-program (4)

CGDI-BMW-FEM-program (5)

CGDI-BMW-FEM-program (6)

Use the CGDI Prog BMW to write the calculated new data to the 95XXX EEPROM chip, then put the FEM/BDC back into the car, thn click on Next

CGDI-BMW-FEM-program (7)

Car battery voltage: 11.93V

Prepare the programming ECU

Security authentication is in process

Safety certification through

The ECU is being programmed

CGDI-BMW-FEM-program (8)

Please remove the FEM/BDC and then use the CGDI Prog programmer to read and save data from the P5XXX EEPROM chip on the FEM/BDC computer board, then click on Next

CGDI-BMW-FEM-program (9)

Setting code

Coding is successful

CGDI-BMW-FEM-program (10)

CGDI-BMW-FEM-program (11)

FEM/BDC key matching need to enter engine ISN, please select the way of input ISN code

CGDI-BMW-FEM-program (12)

OBD is connecting

OBD KWP-CAN 500kbps connection is successful

CGDI-BMW-FEM-program (13)

Loading the code data file

CGDI-BMW-FEM-program (14)

CGDI-BMW-FEM-program (15)

CGDI-BMW-FEM-program (16)

Coding is successful

 

xhorse-vvdi2-bmw-fem-bdc-program

3 Xhorse VVDI2 BMW FEM/BDC coding/programming 

 

 

BMW FEM/BDC Coding/Programming with VVDI2 full kit 4.3.0 above

vvdi2-bmw-fem-programming-2

step 1:

  1. read FEM/BDC coding via OBDII or on the bench
  2. you’d better not close this window after starting this procedure

 

step 2:

  1. open FEM/BDC shell, find out where the 95128/95256 chip is, read EEPROM dump via BDM programmer
  2. load original EEPROM dump and save special EEPROM dump, write special EEPROM dump back to the 95128/95256 chip
  3. restore FEM/BDC shell, provide -12v and connect it via OBD

 

step 3:

  1. this operation requires connecting FEM/BDC on the bench, and make sure you finish step 1 ans step 2
  2. provide +12v to FEM.BDC and connect it via OBD

 

step 4:

  1. open FEM/BDC shell, write original EEPROM dump (read step 2) back to the 95128/95256 chip
  2. restore FEM/BDC shell and connect it via OBD

 

step 5:

loading coding file (read step 1), write to FEM/BDC via OBDII, finish FEM/BDC programming

 

 

Attention please!!!

– You can directly backup/restore coding

– You have to pre-setup the FEM/BDC module before deleting/adding keys or resetting keys

– You’ll be told other tools need to be used first to program the FEM/BDC system, then setup FEM/BDC via VVDI2. It happens when you do FEM/BDC key learning, and you don’t have a working software version

– You’d better not close the VVDI2 interface when you pre-setup FEM/BDC

– You need do with 95128(FEM) or 95256(BDC) chip when pre-setup FEM/BDC

Note: there are two 8-pin chips; do not disassemble the wrong chip; better refer to the wiring diagram

– You must restore original EEPROM data, restore coding when pre-setup FEM/BDC. If you fail to restore coding or the remote cannot start or something wrong with the window (or other failures probably) after coding restore and FEM/BDC installation, please use other tools to do re-coding FEM/BDC

– Ask tech support @obdii365 for help, if the replay sounds continuously after supplying power to the FEM/BDC. Usually, it needs programming.

 

yh-bmw-fem-key-programmer

Yanhua BMW FEM key programmer add a new key

 

There are 5 steps for you to have Yanhua BMW FEM/BDC programmer add/program a new key.

 

Step 1: backup (read) coding data

Step 2: update/program ECU

Step 3: program/learn (add) key

Step 4: restore (write) coding data

Step 5: delete keys disabled

 

How to Program BMW FEM key with Yanhua BMW FEM/BDC programmer

In summary,

all tools above (Lonsdor K518ISE, CGDI BMW, VVDI2, Yanhua BMW FEM/BDC key programmer) can work good in FEM/BDC programming. So, Lonsdor K518ISE vs CGDI BMW vs Xhorse VVDI2 vs Yanhua tool, which best for OBD program BMW FEM/BDC? it depends on your budget and future use.

 

For BMW only: CGDI Prog BMW or Yanhua BMW FEM/BDC key programmer

For VAG+BMW: Xhorse VVDI2 is the best solution.

For universal key programming: Lonsdor K518ISE key programming machine never fails.

 

CGDI BMW price: us$629

Yanhua FEM/BDC programmer price: US$529

Lonsdor K518ISE price: US$1199

Xhorse VVDI2 BMW: US$1029

http://blog.obdii365.com/2017/10/30/program-bmw-fem-key-by-vvdi2-k518-cgdi-or-yanhua-fem/

Lonsdor K518 Program Ferrari 4558 remote via OBD

Lonsdor K518ISE key programmer is able to program remote key on Ferrari 458, F12 and F149 currently. Here’s the guide on programming Ferrari 458 remote with K518.

Procedure:

Step 1: Backup immo data

Step 2: Program key

Step 3: Program remote

Step 1: Backup Immo Data
Connect K518ISE host with vehicle via diagnostic socket
Select Immobilzation->Ferrari->458->Immobilizer->
lonsdor-k518ise-ferrari-1
lonsdor-k518ise-ferrari-2
lonsdor-k518ise-ferrari-3
Select Backup Immo Data function
lonsdor-k518ise-ferrari-4
Turn ignition ON
Communicating
K518ISE will show hardware and software information
lonsdor-k518ise-ferrari-5
Turn ignition OFF
Reading immo data, wait for 6 minutes
lonsdor-k518ise-ferrari-6
Lonsdor K518ISE will read Ferrari 458 pin code and key security data after 6 minutes
write down the pin code
lonsdor-k518ise-ferrari-7
save immo data as bin format
lonsdor-k518ise-ferrari-8
Backup success
lonsdor-k518ise-ferrari-9
Step 2: Program Key

Select Program Key function
lonsdor-k518ise-ferrari-10
The original working key also need to program.
New key to program must be a customized or a pre-written key
lonsdor-k518ise-ferrari-11
Turn ignition ON
Lonsdor K518 then will require to enter PIN code to access
Enter 5-digit pin code and confirm
lonsdor-k518ise-ferrari-12
Number of keys programmed: 1
Press YES to program next key or press NO to go back
lonsdor-k518ise-ferrari-13
Program key complete
lonsdor-k518ise-ferrari-14
Step 3: Program Remote
Select Program Remote function
lonsdor-k518ise-ferrari-15
Turn ignition ON
Again enter PIN code here
lonsdor-k518ise-ferrari-16
Hold remote key to be programmed in hand
Click OK
Click on remote control for 3 sec within 15 sec
press any button on remote key for 3 sec
lonsdor-k518ise-ferrari-17
lonsdor-k518ise-ferrari-18
Number of remote control programmed: 1
Press YES to program next remote
lonsdor-k518ise-ferrari-19
Program remote complete.
lonsdor-k518ise-ferrari-20http://lonsdor-k518ise.blogspot.com/

Lonsdor K518 Adds Renault Koleos 2011 Smart Key

Here’s the detail guide on programming a smart key on a Renault Koleos 2011 with Lonsdor K518 key programmer.

 

Key information:

Original key: 4-button smart key

Frequency: 433MHz

Chip Type: 46 chip

Car slot: in front of the shift lever

Disassemble component: BCM under steering wheel

Device to read BCM eeprom: Xhorse VVDI Prog programmer

Device to program smart key: Lonsdor K518ISE key programmer

lonsdor-k518-koleos-1

lonsdor-k518-koleos-2

Step 1: Remove BCM

Disassemble BCM immo box and find CPU chip XDT384

lonsdor-k518-koleos-3

lonsdor-k518-koleos-4

lonsdor-k518-koleos-5

lonsdor-k518-koleos-6

lonsdor-k518-koleos-7

lonsdor-k518-koleos-8

lonsdor-k518-koleos-9

Step 2: Read EEPROM data with VVDI Prog

Open VVDI-Prog software

Select Renault-BCM-XDT384

lonsdor-k518-koleos-10

Follow vvdi programmer wiring diagram to connect

lonsdor-k518-koleos-11

lonsdor-k518-koleos-12

Read eeprom data and save data to bin format

lonsdor-k518-koleos-13

lonsdor-k518-koleos-14

Connect K518 host with laptop via USB cable

You will see “customfile” folder on K518 software

Copy the eeprom bin file to “customfile” folder

lonsdor-k518-koleos-15

Step 3: Program Smart Key

Re-install BCM from car

Connect Lonsdor K518 key programmer with vehicle via diagnostic socket

Select Renault->By System->Smart Key->Immobilizer system 2->Program smart key

lonsdor-k518-koleos-16

lonsdor-k518-koleos-17

lonsdor-k518-koleos-18

lonsdor-k518-koleos-19

lonsdor-k518-koleos-20

Press on the Start button, press YES to continue

lonsdor-k518-koleos-21

Open the door on driver side

lonsdor-k518-koleos-22

Lonsdor K518ISE shows unable to identify pin code automatically.

Follow guides below: (We have done 1 and 2)

  1. Connect K518 host with laptop via USB cable. You’ll see “customfile” folder

2. Copy eeprom bin file to  “customfile” folder

3. select eeprom bin file on  “customfile” folder

lonsdor-k518-koleos-23

Select Renault BCM data.bin

lonsdor-k518-koleos-24

Insert a new smart key to be programmed into the card slot

lonsdor-k518-koleos-25

lonsdor-k518-koleos-26

Configuring system

Program success. Press YES to program next key

lonsdor-k518-koleos-27

Insert next smart key into card slot

Program success.

Remove smart key

lonsdor-k518-koleos-28

Key learning success

lonsdor-k518-koleos-29

Done.

http://www.obdii365.com/producttags/lonsdor-k518ise.html

Lonsdor K518ISE Program Porsche Macan Turbo Smart Key by OBD

Here’s the step-by-step guide on programming smart key on a  porsche macan turboby using Lonsdor K518ISE key programmer.
Requirements:
2 keys to be programmed
Read BCM data before programming
Lonsdor K518 key programmer
lonsdor-k518ise-Macan-1
Guide:
Connect K518ise host with vehicle via diagnostic socket
Turn ignition switch to ON position
Come to Immobilization->Porsche->Macan->Macan Turbo->Smart Key->Program Smart Key
lonsdor-k518ise-Macan-2
lonsdor-k518ise-Macan-3
lonsdor-k518ise-Macan-4
lonsdor-k518ise-Macan-5
lonsdor-k518ise-Macan-6
Use programmer to read BCM (D-brights/1N35H EEPROM) data, i.e XprogVVDI Prog. Save it as. BIN format and import it into the customfile folder.
Press OK to upload bin file
lonsdor-k518ise-Macan-7
lonsdor-k518ise-Macan-9
Lonsdor K518 will display vehicle VIN, press OK to confirm
lonsdor-k518ise-Macan-10
Please do following:
1.All keys need to learn, otherwise it cannot start vehicle. Recommend to learn the original keys before learning new key (battery must be installed)
2. New key added must be the dealer key generated by car BCM data or key ordered by VIN code
3.Insert key into induction hole when learning key. For smart key, remove the mechanical flip key from keyhole and insert it into induction hole to program.
lonsdor-k518ise-Macan-11
lonsdor-k518ise-Macan-12
Turn ignition to ON
lonsdor-k518ise-Macan-13
lonsdor-k518ise-Macan-14
Communicating…please wait
Lonsdor K518ISE will display vehicle VIN and part number, press OK to confirm
lonsdor-k518ise-Macan-15
Identified number of programmed keys in car: 2
lonsdor-k518ise-Macan-16
Enter key number to be programmed, here we are going to program  2 keys
lonsdor-k518ise-Macan-17
Building communication
Current dashboard display: 02-00
Note: if the programming success, the dashboard  will turn on automatically
lonsdor-k518ise-Macan-18
lonsdor-k518ise-Macan-19
K518 shows current key ID and programming processing
lonsdor-k518ise-Macan-20
Insert new key into ignition switch
Current dashboard display: 02-01
Note: if the programming success, the dashboard  will turn on automatically
lonsdor-k518ise-Macan-21
lonsdor-k518ise-Macan-22
Remove key and insert 2nd key within 30 sec, turn ignition ON
lonsdor-k518ise-Macan-23
Lonsdor K518 shows 2nd key current ID and programming
lonsdor-k518ise-Macan-24
Remove key, all keys involved in programming need to click the unlock button once
lonsdor-k518ise-Macan-25
Program success
lonsdor-k518ise-Macan-26
Program smart key success will automatically generate remote
Test the new smart key
lonsdor-k518ise-Macan-27