Category Archives: odometer correction tool

Will Digiprog3 change mileage for Porsche?

Possible to use Digiprog 3 v4.94 for Porsche Cayman odometer correction?
Yes. Here is the Cayman with chip types confirmed to work:
Porsche Cayman 93C86
Porsche Cayman MCU 35P08
Porsche Cayman 2010 95640
Porsche Cayenne Diag
In detail…

Porsche Cayman 93C86

Note Tacho Meter Value
Dismantle Tacho
digiprog3-porsche-93c860-change-km-1

 

digiprog3-porsche-93c860-change-km-2
Identify Chip 93C86
Desolder Chip 93C86
Clean Chip 93C86
Set Plug ST01 on Chip
digiprog3-st01-adapter
Red Cable on PIN 1
Font readable / PIN 1 bottom left
Choose programm
PKW/LKW—Porsche-Cayman-93C86
Data Back up / Data restore
Data Back up EEPROM
Chip type
Read Data
Write Data
or
Data restore EEPROM
Load Data
Connect replace tacho
Choose Vehicle program
Enter KM value and confirm Entry
Programming operation completed

Porsche Cayman MCU 35P08

Note Tacho Meter Value
Dismantle Tacho
digiprog3-porsche-35p08-change-km-1

 

digiprog3-porsche-35p08-change-km-2
Choose programm
PKW/LKW—Porsche-Cayman-93C86
Data Back up / Data restore
Data Back up EEPROM
Chip type
Read Data
Write Data
or
Data restore EEPROM
Load Data
Connect replace tacho
Choose Vehicle program
Enter KM value and confirm Entry
Programming operation completed

Porsche Cayman 2010 95640

Note Tacho Meter Value
Dismantle Tacho
digiprog3-porsche-95640-change-km-1

 

digiprog3-porsche-95640-change-km-2
Identify Chip 95640
Desolder Chip 95640
Clean Chip 95640
Set Plug ST01 on Chip
digiprog3-st01-adapter
Red Cable on PIN 1
Font readable / PIN 1 bottom left
Choose programm
PKW/LKW—Porsche-Cayenne-2010-95640
Data Back up / Data restore
Data Back up EEPROM
Chip type
Read Data
Write Data
or
Data restore EEPROM
Load Data
Connect replace tacho
Choose Vehicle program
Enter KM value and confirm Entry
Programming operation completed

Porsche Cayenne Diag

Note Tacho meter value
Diagnosis connection is located Engine Compartment
digiprog3-porsche-diag-1

 

digiprog3-porsche-diag-2
Connect Diagnosis Port with Plug 16
Ignition on
Connect DigiProg about Plug 16
The DigiProg needs no separate electricity supply, it is
supplied about the diagnosis port
choose program
PKW/LKW– Porsche-Cyenne-Diag
Enter KM value and confirm Entry
Programming operation completed
digiprog3-porsche-car-list
Porsche 911 (996)
Porsche 911 (996)Turbo
Porsche 928
Porsche 987
Porsche 996 09/01/2000 Diagnostic
Porsche 996 2000/2002 BCU Programming Via Box
Porsche 996 Turbo Ready Soon
Porsche 996 to 08/01 Diagnosis
Porsche 996 up 09/01 93C86 Diagnostic
Porsche 997
Porsche 997 MCU Program via chip
Porsche 997 Tacho & MCUs
Porsche Boxster (9686/987)
Porsche Boxster Diagnosis
Porsche Cayenne 2002-2010
Porsche Cayenne 2010 – to PRESENT YEAR
Porsche Cayenne Diagnostic
Porsche Cayman (987)
Porsche Cheyenne
Porsche Panamera]

Xtool X100 Pad2 Change Mileage on Seat Leon 2015 MQB

New test report: one of our customer has successfully corrected odometer on a Seat Leon 2015 MQB system using Xtool X100 Pad2 full version.

Note: X100 Pad2 only full version can change mileage for part of VAG MQB.  Xtool EZ500/PS80 does same job.
Connect X100 pad with vehicle via OBD
Select Odometer Adjustment function->Seat->Leon->MQB (2014.06-)
xtool-x100-pad2-seat-mqb-change-km-1

 

xtool-x100-pad2-seat-mqb-change-km-2

 

xtool-x100-pad2-seat-mqb-change-km-3
Only continental and VDO are supported, and more dashboard types are under development
xtool-x100-pad2-seat-mqb-change-km-4
Turn on ignition switch but don’t start engine
X100 Pad2 read current mileage which is the same as displayed on dashboard
xtool-x100-pad2-seat-mqb-change-km-5
Manually enter mileage you desired and confirm
xtool-x100-pad2-seat-mqb-change-km-6
 Communicating and writing data in progress
xtool-x100-pad2-seat-mqb-change-km-7
Change mileage succeed
xtool-x100-pad2-seat-mqb-change-km-8
Check new mileage on dashboard
xtool-x100-pad2-seat-mqb-change-km-9
Done.

OBDSTAR X300M Adds Volvo Benz Fiat Mileage Correction

OBDSTAR X300M mileage programmer released new upgrade and adds Mercedes Benz, Volvo, Fiat, VW Audi MQB odometer correction by OBD.
Update! OBDSTAR x300M Benz odometer mileage car list
BENZ V30.24
BENZ
GL Series
X164
ML Series
W164
R Series
W251
BENZM
A Series
W169
B Series
W245
C Series
W203(2007.04-)
W204
CLK Series
C207(E-COUPE)
W209
CLS Series
W218(2011-)
E Series
A207(E-CABRIO)
W211
W212
G Series
W463
GL Series
X164
GLK Series
X204
ML Series
W164
R Series
W251
SLC Series
R197
SLK Series
R171
BENZH
A Series
W169
W176
B Series
W245
W246
C Series
W203(2007.04-)
W204
W205
CLA Series
W117
CLK Series
C207(E-COUPE)
W209
CLS Series
W218(2011-)
E Series
A207(E-CABRIO)
W211
W212
G Series
W463
GL Series
X164
GLK Series
X204
ML Series
W164
W166
R Series
W251
S Series
W221
W222
C216
SL Series
R231
SLC Series
R197
SLK Series
R171
R172
Update! OBDSTAR x300 M VAG MQB odometer mileage car list
Audi
Q2 MQB 2014.06-
A3 MQB 2014.06-
Q2 MQB 2014.06-
Seat
MQB 2014.06-
Leon MQB 2014.06-
Toledo MQB 2014.06-
Skoda
Skoda MQB 2014.06-
Fabia MQB 2014.06-
Octavia MQB 2014.06-
Rapid MQB 2014.06-
Superb MQB 2014.06-
VW
VW MQB 2014.06-
Golf MQB 2014.06-
GOLF7 MQB 2014.06-
Passat B8 MQB 2014.06-
Polo MQB 2014.06-
Tiguan MQB 2014.06-
Touran MQB 2014.06-
Update! OBDSTAR x300M Volvo mileage correction car list
VOLVO V31.00
VOLVO
By Dash
DASH Detect
0L85D
1M80F
1M80F(CAN 500K)
1K78X
1H56A
3K91D
3L16Y
4F73K
By Car
S40
2007-(3L16Y)
S50
2007-(3L16Y)
S60
2000-2001(4F73K)
2001-2002(3K91D)
2003-2007(0L85D)
2007-
Type1(1K78X)
Type2(1K78X)
S80
1999-2000(1H56A)
2000-2001(4F73K)
2001-2002(3K91D)
2003-2007(0L85D)
2010-(1M80F)
V40
2003-2007(0L85D)
2012-(1M80F 500K)
V50
2003-2007(0L85D)
2007-(3L16Y)
V70
1999-2000(1H56A)
2000-2001(4F73K)
2001-2002(3K91D)
2003-2007(0L85D)
2008-(1K78X)
XC60
2007-
Type1(1K78X)
Type2(1K78X)
2012-(1M80F 500K)
XC70
2001-2002(3K91D)
2003-2007(0L85D)
2007-
Type1(1K78X)
Type2(1K78X)
2010-(1M80F)
XC90
2001-2002(3K91D)
2003-2007(0L85D)
2008(1K78X)
Update! OBDSTAR x300M Fiat odometer correction car list
FIAT V31.03
ODOMETER_MILEAGE
500
500
500L
500 TFT
500X
Type 1
Type 2
500X TFT
Albea
95040
Brava
95040
Bravo
95040
Croma
95040
Doblo
95040
2011
2015
Ducato
95040
2011-
2015
Fiorino
Freemont
2012
Grande punto
Idea
95040
Linea
95040
Marelli(Auto)
Palio
95040
MM95160
VDO
Panda
95040
2012
Punto
95040
95160 2015
EVO
Qubo
Siena
VDO
Stilo
HC  -2005
HCS 2005-
Strada
VDO
TORO
2016
2017
Uno way
VDO
MM 2015
http://blog.obdii365.com/2018/09/19/obdstar-x300m-adds-benz-volvo-fiat-mqb-obd-odometer-correction/

Digiprog 3 VW Golf Odometer Correction: Yes or No?

Does Digiprog 3 china clone work for VW Golf odometer correction?

Confirm! It worked fine!

VW Golf 6: OBD – OK

VW Golf 5: OBD – OK

VW Golf 4: OBD – OK

VW Golf 3: OBD – OK

in detail…

Part 1: Digiprog 3 Golf 6

Golf 6 2012: done by OBD – OK

Golf 6 2011: i can change odometer with digiprog 3 china clone via OBD

But it also depends on quality of your clone too..

Golf 6 2011: VDO tacho obd 2 min !!ok!!

Golf 6 2011: ok through OBD

Golf 6 2011: read/write ok in 5min

Golf 6 2011: not work with Nec 24c64

Golf 6 2011: Dash MM read old value ok and write ok, But dash now say: Error and not show value

Try different value and double check which version of dash is

Yes, this car work without dash

Golf 6 2011 MM5: obd ok

Golf 6 m.m 2011: done by obd in 5 minutes,work

VW golf 6 2010: OBD OK

Golf 6 2009: change km no issues via OBD

VW Golf mk6 2009: OBD is good with error clearing

Golf 6 2009: convertible OBD – OK

Part 2: Digiprog3 Golf 5

Golf 5: ecu works diag

Golf 5 2008: ok through OBD

VW golf 5 2008: OBD OK

GOLF 5 2008 kombiistrument 3HL: OBD -OK 1min

GOLF 5 2008 ECU DIAG R4 1,9L EDC 000SG: OBD-ok 10min

Golf 5 2007: ODO AND ECU EDC16 ok

VW golf 5 2007: OBD tacho OK, ecu OBD OK

Golf 5 2005 2006 2007: OBD change km

Golf 5 2006 1,9 tdi: obd OK

Golf 5 2006: odo and ecu OK

VW golf 5 2003: OBD no connection

Golf 5 edc16: all ok

Golf 5: obd ok

VW Golf MK5 2.0 TDI 140cv DSG BKD Engine:

Dash kms : OK

DSG kms: OK

ECU Diag: Unknown version, not read

Service: OK

Golf 5 Dash Visteon 95160: less than a minute OK

Golf 5 ECU EDC16: 6~8 minutes OK

Golf mk 5 2006: ok through OBD

VW Golf mk5 2006: dash+ edc16 OBD is good

Part 3: Digiprog 3 Golf 4 Golf 3:

Golf 3 & Golf 4: works OK via dash connector and via OBD

Golf 4 19tdi 2000: change mileage OK

Golf mk4: obd ok

VW golf 4 2004 tdi: OBD OK

VW golf 4 2002: bosch OBD OK

Golf 4: vdo ok edc 15 not work

Part 4: Digiprog 3 old version 4.88 and Golf

Digiprog 3 v4.88: worked

I have china clone version 4.88 and it worked fine.

Digiprog 3 v4.88: worked

I use always my DP3 4.88 with many golf 6 and no problem !

Digiprog 3 v4.88: not worked

My DP3 v4.88 damaged the eeprom content, and

apart from not changing km, the backlight is always on

Digiprog 3 v4.88: not worked

DP3 v4.88 does not work with MM5 dash (NEC mcu)

Tested on Golf variant 2010 and 2011

IMPORTANT TIP:

You’d better have Digiprog 3 v4.94 for odometer correction.

It works for more cars than v4.84.

Look here: Digiprog 3  4.94 on Golf 5 odometer correction



Tech support from obdii365.com

Digiprog3 Clone Change Smart ForTwo Mileage by OBD

Purpose: Change the mileage of a Smart Fortwo 2002 via an OBDII cable
Car: Smart ForTwo CM01 – year 2002
smart-fortwo-1
smart-fortwo-2
Odometer correction tool: Digiprog 3 Chinese version
Method: ODB2
Issues:
Digiprog 3 says “NO CONNECTION”.
Suggestion & Solutions:
2002 cannot be done via obd!!
First you have to reset the bcu and then correct the milage in the dash (its a eeprom C66).
Setting the eeprom worked fine.
Note 1: Wrong Pinouts
Sometimes Chinese cable schematics is wrong.
Note 2: What is BCU?
BCU= Bord Control Unit.
is under the steering wheel on the left side. (inside the reilais box). you have to dismount it and connect like in the manual. until now i couldnt find the right pinout for the Digiprog(im seraching). For me it worked only with “Tacho Pro”.
In the dash you can find two C66 eeproms you need the right one. You have to connect the red wire with the lower left leg of the eeprom (i couldnt connect it with the clip it worked only by soldering every single wire).
Here is the manual:
Requires plug ST01
digiprog-plug-st01-1
digiprog-plug-st01-2
SMART TACHO CHIP:
Remove the instrument cluster disassemble it.
Find the chip 93CS66.
digiprog-smart-fortwo-1
Put plug ST01 on the chip (read red wire on pin 1 writing from chip then bottom left is pin 1).
Select the program: Car / Truck – SMART C66.
digiprog-smart-fortwo-2
The DIGIPROG 3 v4.94 will show you the current / incorrect KM status.
Enter the new / correct KM-Stand.
FINISHED.

Peugeot Citroen BSI Odometer Reset with OBDSTAR X300 DP

OBDSTAR X300 DP/Key Master DP/OBDSTAR H108 free updated PSA BSI odometer correction function in February, 2018.   Here are photos and videos guides on BSI mileage reset by X300 DP.
X300 DP PSA BSI Function List:
x300-dp-psa-odometer-correction
Example 1:
OBDSTAR X300 DP tablet reset odometer in Peugeot Siemens K-line BSI E02
Remove BSI module from vehicle
obdstar-x300-dp-peugeot-bsi-reset-1
Connect BSI with X300 DP main unit and VCI interface
obdstar-x300-dp-peugeot-bsi-reset-2
Select Diag Program->Cluster Calibrate->Peugeot->Peugeot V30.72->BSI->Manual Select (select BSI type)
obdstar-x300-dp-peugeot-bsi-reset-3
obdstar-x300-dp-peugeot-bsi-reset-4
obdstar-x300-dp-peugeot-bsi-reset-5
Here we select SIEMENS BSI-E0X/BSI-FOX
obdstar-x300-dp-peugeot-bsi-reset-6
Turn ignition switch to ON position
You can read/write eeprom and change odometer in this BSI
First select Read EEPROM
obdstar-x300-dp-peugeot-bsi-reset-7
Reading eeprom data
obdstar-x300-dp-peugeot-bsi-reset-8
Save eeprom bin file
obdstar-x300-dp-peugeot-bsi-reset-9
Select Mileage adjustment
You should read and save eeprom data before resetting odometer
obdstar-x300-dp-peugeot-bsi-reset-10
OBDSTAR X300 DP read current mileage and confirm
obdstar-x300-dp-peugeot-bsi-reset-11
Manually enter mileage you desired
obdstar-x300-dp-peugeot-bsi-reset-12
Peugeot BSI E02 odometer reset success.
obdstar-x300-dp-peugeot-bsi-reset-13
obdstar-x300-dp-peugeot-bsi-reset-14
Done.
Example 2:
OBDSTAR Key Master DP Odometer Reset for Citroen BSI 04EV2 KE1
Similar procedure is performed, check picture guides
obdstar-x300-dp-citroen-bsi-reset-1
obdstar-x300-dp-citroen-bsi-reset-2
obdstar-x300-dp-citroen-bsi-reset-3
obdstar-x300-dp-citroen-bsi-reset-4
obdstar-x300-dp-citroen-bsi-reset-5
obdstar-x300-dp-citroen-bsi-reset-6
obdstar-x300-dp-citroen-bsi-reset-7
obdstar-x300-dp-citroen-bsi-reset-8
obdstar-x300-dp-citroen-bsi-reset-9
Done.
OBDSTAR X300 DP PSA Peugeot Citroen BSI OBD Odometer Reset Videos 
OBDSTAR X300 DP Reset Odometer for Peugeot BSI S02
OBDSTAR X300 DP Reset mileage for Peugeot BSI Q03
OBDSTAR X300 DP Reset Odometer for Peugeot BSI E02
OBDSTAR X300 DP Reset Odometer for Citroen BSI 04EV2 KE1
OBDSTAR X300 DP Reset Odometer for Citroen BSI 04EVK05
More video guides, please subscribe our Youtube channel: http://www.youtube.com/user/obd365
http://blog.obdii365.com/2018/02/25/obdstar-x300-dp-reset-odometer-in-psa-peugeot-citroen-bsi/

How to change Mileage on VW Polo 2006 VDO with OBDSTAR H110

We’ve tested OBDSTAR H110 VAG key programmer / mileage programmer and confirmed it’s working. Here is the test report.
Date: Feb. 7th, 2018
Tech support: professionals working for obdii365.com
Device: OBDSTAR H110 Immo and Odometer programmer
It is a new device designed for VAG dashboard odometer correction (incl. MQB and NEC+24C64 2014-) and key programming (incl. VAG-I+C Immobilizer).
Car: 2006 VW Polo
Test procedure:
Video:
https://youtu.be/qy3lDJEf1dY
Upload photos…
Dashboard status
obdstar-h110-polo-vdo-1
Connected to Obdstar H110 odometer correction tool and power on
obdstar-h110-polo-vdo-2
Select a car for odometer correction
VEHICLE
obdstar-h110-polo-vdo-3
CLUSTER CALIBRATE
obdstar-h110-polo-vdo-4
VW
obdstar-h110-polo-vdo-5
VW V31.59
obdstar-h110-polo-vdo-6
Loading Obdstar H110 VW software…
obdstar-h110-polo-vdo-7
Initializing…
Authorizing…
Select from vehicle
obdstar-h110-polo-vdo-8
Polo
obdstar-h110-polo-vdo-9
VDO K line
obdstar-h110-polo-vdo-10
Communicating…
obdstar-h110-polo-vdo-11
Reading mileage…usually 2-5 minutes
obdstar-h110-polo-vdo-12
Check and confirm Current mileage: 4192km
obdstar-h110-polo-vdo-13
Polo dashboard displays the mileage: 4193
obdstar-h110-polo-vdo-14
Input the new mileage: 20000
obdstar-h110-polo-vdo-15
obdstar-h110-polo-vdo-16
Adjusting mileage…usually 2-5 minutes
obdstar-h110-polo-vdo-17
Finish odometer correction
obdstar-h110-polo-vdo-18
Exiting…
obdstar-h110-polo-vdo-19
Polo dashboard displays the new mileage: 20001
Complete!
Result: Obdstar H110 VAG worked good in odometer correction

How to use Lonsdor K518 to change Jaguar XJ 12 mileage

Lonsdor K518ISE key programmer is able to change mileage on Jaguar XJ, F-type, and XE 2015 up (some pre-2015) models. Here’s demo guide on XJ year 2012 (Middle East model) odometer correction with K518ISE by OBD.
lonsdor-k518-change-jaguar-xj-km-1
A Jaguar XJ year 2012 running 157,999 km.
Connect K518 host with vehicle
Select Odometer Adjustment function->Jaguar->XJ->Odometer correction
lonsdor-k518-change-jaguar-xj-km-2
lonsdor-k518-change-jaguar-xj-km-3
lonsdor-k518-change-jaguar-xj-km-4
Turn ignition on
lonsdor-k518-change-jaguar-xj-km-5
Communicating
Manually enter mileage you desired, i.e: 141,000 km and confirm
lonsdor-k518-change-jaguar-xj-km-6
Change mileage in progress
lonsdor-k518-change-jaguar-xj-km-7
Dashboard instrument turns black during the procedure, it is normal. When change km is done, it will reset instrument.
lonsdor-k518-change-jaguar-xj-km-8
lonsdor-k518-change-jaguar-xj-km-9
Jaguar XJ mileage correction is done.
Turn ignition off and on
lonsdor-k518-change-jaguar-xj-km-10
lonsdor-k518-change-jaguar-xj-km-11
Lonsdor k518 key programmer automatically erase the fault code existed
lonsdor-k518-change-jaguar-xj-km-12
lonsdor-k518-change-jaguar-xj-km-13
Done.
Reference:

Audi A8 2003 Up Odometer Correction with Digiprog 3

Digiprog 3 v4.94 odometer correction tool how to use for Audi A8 (2003-). Here are notes for you all, of Tacho meter value
Audi A8 (2003-)
audi-a3-2003
Diagnostic connection is located in the cabin
digiprog3-audi-a3-1
Connect Diagnosis Port with DP3 cable of Plug 16
digiprog3-audi-a3-2
Ignition on
Connect the DigiProg 3 main unit to Plug 16
The DigiProg needs no separate electricity supply; it is supplied via the diagnosis port
Follow DigiProg3 v4.94 instruction and change KM
digiprog3-audi-a3-3
digiprog3-audi-a3-4
Enter KM value and confirm Entry
Audi A8 mileage correction completed!
Before:
digiprog3-audi-a3-5
After:
digiprog3-audi-a3-6
Job’s done!
Note: If error message “Access denied” pops up, pls. choose:
PKW/LKW-Audi-A8-2003-(4E) 1. Flash Cxxx/
Dxxx
Confirm with Hook
Remove fuse 5 + 10
Wait approx. 5 seconds
Reinstall fuse
if tacho meter is dark
Switch Ignition on and off
Choose program:
PKW/LKW– Audi—A8-2003-(4E) Diag
Enter KM value and confirm Entry.