Vxdiag Vcx Nano GM Do Online Programming on Buick GL8 2008

Vxdiag Vcx Nano for GM/Opel online programming test report… Here you go. Definitely work perfectly on a 2008 Buick GL8 car. Both OK in ECM & TCM online programming!

 

 

Using: Vxdiag Vcx Nano for GM diagnostic tool

 

Car: Buick 2008 GL8 Firstland

Engine: (C) 3.0L V6 LZC

 

Purpose: ECU programming

Modules to be programmed: ECM, TCM

 

Online/ offline: online

 

 

How to program Buick ECM & TCM with Vxdiag vcx nano for gm:

Accept the terms and conditions of use

vxdiag-vcx-nano-gm-online-programming-1

Read the service and programming information

vxdiag-vcx-nano-gm-online-programming-2

Access your subscription

vxdiag-vcx-nano-gm-online-programming-3

vxdiag-vcx-nano-gm-online-programming-4

Go to service programming system

vxdiag-vcx-nano-gm-online-programming-5

Start SPS (skip the driver installation)

vxdiag-vcx-nano-gm-online-programming-6

vxdiag-vcx-nano-gm-online-programming-7

Select diagnostic tool: J2534 VXDIAG and programming process: Programming ECU

vxdiag-vcx-nano-gm-online-programming-8

vxdiag-vcx-nano-gm-online-programming-9

vxdiag-vcx-nano-gm-online-programming-10

Connect J2534 device (vxdiag vcx nano gm) to the vehicle and PC:

Turn ignition off

Verify the vehicle battery fully charged

Turn ignition on, engine off

Connect the J2534 device to Data Link Connector

Connect the J2534 device to the PC

Switch the J2534 device on and wait for the device to get ready

After programming, the technician will be given the opportunity to clear diagnostic trouble codes from all ecus on this vehicle. The technician may want to record DTCs and freeze frame data before continuing.

 

Select a car: Buick 2008 passenger car GL8 Firstland (C) 3.0L V6 LZC

vxdiag-vcx-nano-gm-online-programming-11

Vin, then next

vxdiag-vcx-nano-gm-online-programming-12

SPS supports CCP, ECM, PSDM, TCM controllers to program

Here: normally program engine control module (ECM)

vxdiag-vcx-nano-gm-online-programming-13

Next

vxdiag-vcx-nano-gm-online-programming-14

Continue

vxdiag-vcx-nano-gm-online-programming-15

vxdiag-vcx-nano-gm-online-programming-16

Reprogramming….finished

vxdiag-vcx-nano-gm-online-programming-17

ECM Programming complete!

vxdiag-vcx-nano-gm-online-programming-18

Follow the specific controller instruction:

M5741: clearing DTCs will erase stored history data from all controllers on the Data Link Connector currently in use. Move your interface to any additional Auxiliary Data Connectors on the vehicle to clear DTCs from other controllers. When finished, return the interface to the Data Link Connector.

Crankshaft Postion Variation Relearn Procedure using Special Function on TECH2 may be needed after programming. Refer to Service Manual DTC P1336/ p0315.

 

Next to normally program transmission control module (TCM), the same

vxdiag-vcx-nano-gm-online-programming-19

vxdiag-vcx-nano-gm-online-programming-20

vxdiag-vcx-nano-gm-online-programming-21

vxdiag-vcx-nano-gm-online-programming-22

vxdiag-vcx-nano-gm-online-programming-23

vxdiag-vcx-nano-gm-online-programming-24

vxdiag-vcx-nano-gm-online-programming-25

vxdiag-vcx-nano-gm-online-programming-26

TCM Programming complete!

 

Have fun!

http://blog.obdii365.com/2017/03/30/vxdiag-vcx-nano-gm-program-buick-gl8-ecm-tcm-online/

0

Leave a Reply

Your email address will not be published. Required fields are marked *